Removal, installation, assembly and dismantling of block K/century of Nissan Micra (since 2002 of release)
Service and to Nissan Micra car repairs (since 2002 of release)
1. Introduction
2. Governing bodies and operation receptions
3. Settings and routine maintenance of the car
4. Engine
5. Systems of cooling of the engine, heating, ventilation and air conditioning
5.1. System of cooling of the engine
5.2. Systems of heating, ventilation and air conditioning
5.2.1. General information
5.2.2. Correction of level of a coolant
5.2.3. Removal, installation, dismantling and control unit assembly by ventilation system with a heater and To/in
5.2.4. Removal, installation, assembly and To/in block dismantling
5.2.5. Removal and installation of a radiator of a heater
5.2.6. Removal and installation of the electromotor of the fan of a heater
5.2.7. Removal and installation of assembly of the resistor of the fan and To/in system sensors
5.2.8. Adjustment of cables of a drive zaslonok
5.2.9. Removal and installation of electromotors of a drive zaslonok
5.2.10. Removal and installation of air lines and deflectors
5.2.11. Removal and installation of lines of a coolant and To/in compressor
5.2.12. Removal and installation of other components of To/in system
5.2.13. Self-diagnostics automatic To/in
6. A power supply system and production of the fulfilled gases
7. Systems of electric equipment of the engine
8. Manual box of gear shifting and coupling
9. Automatic transmission
10. Power shafts, rotary fists and stupichny assemblies
11. Brake system
12. Suspension bracket and steering
13. Body
14. Onboard electric equipment
15. Electric equipment schemes
 







f4fb234a

5-2-4-snyatie-ustanovka-sborka-i-razborka-bloka-k-v.html

5.2.4. Removal, installation, assembly and To/in block dismantling

To/in block fixture

Assembly of the To/in block of hand-operated models

1 *, 5, 11,13,23 — the Screw
2* — the aspirator Line
3/15 — the Right/left casing of the fan
4/14 — the Right/left casing
6/10 — the Right/left air line «to feet»
7 — a cooling Hose
8 — Э / the motor of the fan of a heater
9 — Zaslonka of air mixing
12 — Clamps
16 — the Aspirator
17 — Zaslonka of ventilation
18 — the Rod обдува flew down
19 — Zaslonka обдува flew down
20 — Zaslonka of supply of air to feet
21 — a heater Radiator
22 — the Cover of a tube of a radiator
24 — the Sensor of temperature of the evaporator
25 — Laying of a tube of a radiator
26 — Nizhny a fan casing
27,29 *, 31,33,35* — the Screw
28 — the Arm
30 — E/motor* (draft **) zaslonka of supply of air
32 — resistor Assembly
34 — the Connecting casing

36* — Э / the motor of a zaslonka 9
37 — the Rod of a zaslonka 9
38 — the Lever of a zaslonka 9
39 — the Spring
40,42,57,60 *, 65 — the Screw
41 — the Clamp of a tube of a heater
43 — Bolts
44 — the Broad valve
45 — the Insulator
46 — Salonny the filter
47 — Tyaga* (the lever **) zaslonka 49
48/50 — the Left/right casing of a zaslonka 49
49 — Zaslonka of supply of air
51 — the Evaporator
52 — the Cover of the broad valve
53 — the ventilation Lever / обдува
54 — a ventilation Rod / обдува
55 — Draught of ventilation / обдува
56,58,66 — the Washer
59 — the Rod of a zaslonka of modes
61 — Э / the motor of a zaslonka of modes
62 — the Lever of a zaslonka 20
63 — Draught of a zaslonka 20
64 — the Main zaslonka

 PERFORMANCE ORDER

  1. In the conditions of a specialized workshop discharge К/В system.
  2. Empty system of cooling of the engine (see. The section Replacement of cooling liquid).
  1. Disconnect from the evaporator a flexible hose of low pressure and a tube of a high pressure. To Zakuporta open openings.
  1. Disconnect hoses from a radiator of a heater and закупорьте open openings.

At a detachment of hoses cooling liquid can follow.

  1. Remove the dashboard (see. Head Body), clamps of electroconducting and dashboard rack.
  1. Turn out screws and release air line clamps.
  2. Turn out bolts of fastening of the To/in block, bolts of the steering mechanism and a steering column. Release electroconducting clamps (see an illustration To/in block Fixture).
  3. Remove the onboard control unit (BCM) – see. Head Onboard electric equipment.
  4. Remove the steering mechanism and then the К/В block.
  5. Components of assembly of the To/in block are presented on an illustration Assembly of the To/in block of hand-operated models.
  6. Installation is made upside-down. Replace all sealing rings on tubes. At installation of the To/in block watch that its drainage opening coincided with a drainage tube. Tighten fixture with demanded efforts. In summary fill systems of cooling and To/in and make sure of absence of leaks.



5.2.3. Removal, installation, dismantling and control unit assembly by ventilation system with a heater and To/in

5.2.5. Removal and installation of a radiator of a heater