Audiosystem and mobile phone. Nissan Micra (since 2002 of release)
Service and to Nissan Micra car repairs (since 2002 of release)
1. Introduction
2. Governing bodies and operation receptions
2.1. Access, protection
2.2. Elements of systems of safety
2.3. Car equipment, arrangement of devices and governing bodies
2.4. Devices of ensuring comfort
2.4.1. Traveling computer and multipurpose display
2.4.2. Systems of ventilation, heating and air conditioning
2.4.3. Audiosystem and mobile phone
2.5. Receptions of operation and auxiliary systems
3. Settings and routine maintenance of the car
4. Engine
5. Systems of cooling of the engine, heating, ventilation and air conditioning
6. A power supply system and production of the fulfilled gases
7. Systems of electric equipment of the engine
8. Manual box of gear shifting and coupling
9. Automatic transmission
10. Power shafts, rotary fists and stupichny assemblies
11. Brake system
12. Suspension bracket and steering
13. Body
14. Onboard electric equipment
15. Electric equipment schemes
 







f4fb234a

2-4-3-audiosistema-i-mobilnyjj-telefon.html

2.4.3. Audiosystem and mobile phone

General information and recommendations about audiosystem use

The audiosystem works at the key established in the situation "Acc" or "ON" or the ignition switch. For improvement of quality of reception of broadcasts it is recommended to use the aerial. The aerial can be turned out from its nest located on a roof of the car.

At low temperature or in rainy weather normal operation of the CD player (CD) can be broken. In similar cases it is necessary to take a disk and to dry or air system. When driving on rough roads reproduction of CD can interrupt. For adequate work of a player of CD use blank qualitative disks. The player can not reproduce properly not copied disks (CCCD), and also written-down (CD R) and rewritten (CD-RW) disks. In order to avoid violation of normal work of a player do not use disks in diameter of 8 cm, disks not a round form and disks with paper stickers.

Audioblock

1 — the Switch of power supply of an audiosystem
2 — the Switch of function of a choice of alternative frequencies (AF) of a radio signal
3 — the Nest for compact disc loading
4 — the Button of extraction of a compact disc
5 — the Button of control of a sound of an audiosystem
6 — Manual control of a radio receiver in the top and bottom ranges, buttons of a choice of modes of control of a sound
7 — the Radio receiver: automatic control in the top and bottom ranges; CD player: consecutive transition between records on CD; buttons of installation of adjustable parameters of a sound
8 — the Button of reception of road information (THAT) / such as a radio program (PTY)

9,13 — choice Buttons previously the programmed radio stations
10 — the Radio receiver: the choice button previously the programmed radio station; CD player: the switch of a mode of reproduction of records in casual sequence
11 — the Display
12 — the Radio receiver: the choice button previously the programmed radio station; CD player: switch of a mode of repeated reproduction of records
14 — the Switch of radio ranges of LW, MW, FM
15 — the Switch of a sort of work (SRC)
16 — the Regulator of level of loudness

The audioblock includes the digital radio receiver working in ranges of long (LW), average (MW) and ultra-short waves (FM), and CD player. The audioblock is equipped with system of protection against theft and function of reception of road messages.

The main functions of an audiosystem can be operated by means of the buttons located on a steering wheel. For this purpose the key or the switch of ignition should be in the situation "Acc" or "ON", and the audiosystem should be included. The description of functioning of buttons is provided in separate subsection.

At installation on the car of SV-radio station, the mobile phone or another radio-electronic the equipment it is necessary to observe given below the recommendation, otherwise the established equipment can negatively affect functioning of system of injection of fuel or on other electronic blocks of the car. The SV-radio station aerial a dolzhka to settle down as it is possible further from electronic control units car systems (including and radio station). The antenna cable should settle down not closer than 20 cm from electroconducting of system of injection of fuel. Do not lay an antenna cable near plaits of electroconducting of the car. For elimination of standing radio-waves follow recommendations of the manufacturer of the radio-electronic equipment. Connect a wire the SV-radio station case to "mass" of the car.

System of protection against theft

Without knowledge of an individual code of an audiosystem it cannot be included after installation in other car that considerably reduces risk of its theft.

At normal operation the audiosystem is unblocked and can be used usually. At disconnection of an audiosystem from an onboard electric network the system of protection against theft which blocks the subsequent inclusion of an audiosystem works. To unblock it it is required to enter an individual code. This code cannot be changed and is used only for the concrete car.

The individual code of an audiosystem is given in the card which is given together with operational documentation on the car. Store the code card in a safe place and never leave it in the car. At an uter of the code card of an audiosystem address to the official representative of the Nissan company.

Removal of blocking of an audiosystem and inclusion of a service mode

If the audiosystem is blocked, at its inclusion on the display for two seconds the message of "CODE" which then is replaced with 0000 symbols is deduced.

For blocking removal by means of choice buttons previously the programmed radio stations, enter an individual four-unit code. For example, for input of a code 5169 press the first (1) button of a choice previously the programmed radio stations five a time in a row, then the second, third and fourth buttons respectively 1, 6 and 9 times. In summary confirm code input, having pressed the button ^. If the correct code is entered, the audiosystem will join; otherwise indications of the display will not change and the audiosystem will not join.

At maintenance of the car it is necessary to remove a protective code of an audiosystem that will allow to disconnect the storage battery (for example, for maintenance, etc.) without blocking of inclusion of an audiosystem. For this purpose switch off an audiosystem and, at the same time holding the pressed 1st and 4th buttons of a choice previously the programmed radio stations, again include an audiosystem. Release choice buttons previously the programmed radio stations.

It is not necessary to leave the car without supervision or to put on unprotected parking if the code of an audiosystem was removed. Right after the completion of service of the car activate a protective code, I act in the same way, as well as at its deactivation. Now the system of protection against theft is in an active condition.

Main functions of management by an audiosystem

Power supply switch

Turn a key or the ignition switch in the situation "Acc" or "ON", then press the switch of power supply of an audiosystem and hold it not less than two seconds. The audiosystem will start to work in the same mode (radio or CD playing) in which it worked directly ahead of switching off. Loudness of a sound will be established at level which was programmed previously for audiosystem inclusion (modes of personal control). In the absence of loaded CD on the display there will be «NO DISC» message. The audiosystem joins automatically if to load into it CD then disk playing will begin.

To switch off an audiosystem, hold power supply switch pressed during not less than two seconds or to switch off ignition.

Adjustment of level of loudness and sound shutdown

Pressing buttons «» or «–» a regulator, establish desirable level of loudness.

Shutdown of a sound is made by short pressing the switch of power supply of a CD audiosystem. Thus on the display there is «MUTE» message. Again to include a sound, once again shortly press power supply switch.

Switch of a sort of work (SRC)

This switch allows to choose between a radio receiver or CD player. By each pressing the switch the active operating mode of an audiosystem is reflected in the display. If CD is not loaded, on the display there is «NO DISC» message.

Control of a sound (MOD)

Press the MOD button and hold her in this situation not less than two seconds to enter into the menu of control of a sound. On the display the indicator «MENU ^ v» will light up. By each pressing the button ^ or v occurs switching of modes of control of a sound in cyclic sequence: Bass (LF Level), Treble (VCh Level), Fader (Balance the front/back), Balance (Balance it is left/is right), Loudness (Tone compensation), REG (Reception of local radio stations), Bass etc. Establish desirable parameters of a sound, using in the chosen mode of the button <<or>>.

Levels of LF and VCh are regulated from–7 to 7, and values of balances – from–9 (back/to the left) to 9 (forward/to the right). Tone compensation is used for strengthening of function of lifting of LF. In the REG mode buttons <<or>> it is possible to include or switch off this mode.

After sound control once again press the MOD button to fix in memory of an audiosystem the established levels of adjustments.

When switching a sort of work of an audiosystem (the radio receiver or CD player) are established those settings of a sound (levels of LF/VCh and tone compensation) which were set previously for the relevant source of a sound. At the same time balance control the front/back also it is left/is right from a source of a sound does not depend.

Radio receiver

Switch of radio ranges (BAND)

At everyone short (less than two seconds) pressing the BAND button there is a switching of radio ranges in a cyclic order: FM1, FM2, FMT, MW, LW, FM1 etc.

If to include a FM range and it is long (not less than two seconds) to press on BAND button, will join function of automatic programming of memory of a radio receiver. Thus the radio receiver will automatically find five FM stations with the strongest signal and will bring their frequencies in cells (with the first on the fifth) a memory (FMT range). During automatic programming of memory of a radio receiver on the display there is a message of "T-STORE" and an AS symbol, and the sound is muffled.

If function of reception of road messages (THAT) is included, for entering in memory only those radio stations which transfer road messages are selected.

Manual control of a radio receiver

Manual control of a radio receiver is made by means of buttons ^ (increase in frequency) and v (frequency reduction). Frequency of control changes discretely, the step of change of frequency of control depends on the included radio range and makes 100 kHz in a range of ultra-short waves of FM, 9 kHz in a range of average waves of MW and 3 kHz in a range of long waves of LW.

If to press the button ^ or v and to hold her in the pressed situation more long 0.5 with, frequency of control of a radio receiver will continuously increase or decrease until the button will not be released.

Automatic control of a radio receiver

Automatic control can be carried out at various levels of sensitivity of a radio receiver. If high level of sensitivity of "DX" is included, the receiver will be adjusted on broadcasting radio station next on frequency irrespective of level of an accepted signal. If low level of sensitivity of "LO" is included, control will occur only on radio station to rather powerful signal, that is on local radio stations.

By single pressing the button>> or <<the radio receiver begins search of working station in respectively top or bottom поддиапазоне rather current frequency of control. Search stops, as soon as the radio receiver will be adjusted on the next station on frequency. In the course of automatic control of a radio receiver the sound is muffled.

If a radio receiver, working at a low level sensitivity of "LO", it could not be adjusted in all radio range on one broadcasting station, there will be an automatic switching of a radio receiver on high level of sensitivity of "DX". Then the radio receiver will continue search of broadcasting radio stations in the same range. If now the radio receiver does not find any broadcasting radio station, automatic control will stop.

If function of reception of road messages (THAT) or a choice such as a radio program (PTY) is included, automatic control of a radio receiver is made only on those radio stations which respectively transfer the program of road messages or which programs correspond previously to the chosen type.

Choice previously the programmed radio stations

Radio receiver control for previously programmed stations is made short (less than two seconds) by pressing the corresponding buttons (with the first on the fifth). At long (more long than two seconds) pressing the button there is a reprogramming of the corresponding cell of memory of a radio receiver, that is the current frequency of control of a radio receiver is brought in the memory cell which number corresponds to number of the pressed button.

It is possible to program to 15 FM radio stations (on 5 in ranges of FM1, FM2 and FMT). In ranges of MW and LW it is possible to program also on 5 radio stations.

Mode of scanning of radio stations

To include a scanning mode, press the switch of a sort of work of SRC and hold it not less than two seconds. The radio receiver will start to be adjusted serially on all broadcasting radio stations, since the current frequency of control. In the course of search of radio stations on the display the SCAN indicator will burn. After control for the next radio station reception proceeds within 10 seconds, and on the display the name or frequency of a broadcasting of this radio station is deduced. To switch off a scanning mode, press once again the switch of a sort of work of SRC.

If function of reception of road messages (THAT) or a choice such as a radio program (PTY) is included, automatic control of a radio receiver is made only on those radio stations which respectively transfer the program of road messages or which programs correspond previously to the chosen type.

System of radio data (RDS)

The RDS system allows to hand over at the same time with the main FM radio signal additional information in the coded digital form. The RDS system supports a set of information service functions, for example, such, as: indication on the display of the name of radio station, reception of road messages and local news, automatic search of the radio station transferring the program of a certain genre etc.

Alternative frequencies of a radio signal (AF)

Function of a choice of alternative frequencies of a radio signal (AF) can work in FM radio range, and also at reproduction of records at a compact disc.

The AF function joins short (about two seconds) pressing the AF button.

At the included AF function the following service functions are carried out:

Function of automatic change-over of a radio receiver consists that a radio receiver, comparing capacity of radio signals on all alternative frequencies (from the list of frequencies of AF), automatically chooses and is adjusted on that frequency of a broadcasting on which the best conditions of reception of a broadcast are provided.

Updating of data of the expanded EON network. This function works also at the switched-off AF function. Reception of data of EON allows to recustomize automatically frequencies previously the programmed stations on the same radio network. Besides, there is a possibility of use of the additional service functions provided by a network, for example, reception of road messages. If the radio receiver is adjusted on the RDS station entering into the expanded EON network, on the display the EON indicator burns.

RDS functions

PS function (conclusion to the display of the name of radio station). As soon as the radio receiver is adjusted on RDS radio station (manually or semi-automatic), reception of radio data of RDS begins and on the display the name of accepted station at once is deduced.

Function of interruption of the current mode by an alarm signal [ALARM INTERRUPTION – EBU (European Broadcasting Union) of SPEC FOR INFO]. If the radio receiver receives a code of an alarm signal of "PTY 31", the current operating mode of an audiosystem automatically interrupts and begins message translation. Thus on the display the ALARM indicator lights up. After the warning message will end, the audiosystem will immediately return to an initial operating mode.

REG mode (reception of local radio stations). If to include the REG mode when the radio receiver works in a FM range and it is adjusted on the local radio station transferring local programs, control of a radio receiver will remain and switching on other local radio stations will not occur.

THAT function (reception of road messages). This function can be used at the included range of FM, and also at reproduction of records on CD. THAT function joins short (not more long than two seconds) pressing the THAT button. THAT function can be carried out irrespective of, the AF function is included or switched off. At the included THAT function on the display the THAT indicator burns. If it is short (not more long than two seconds) to press the THAT button, function of reception of road messages will be switched off, and the THAT indicator will go out. If the THAT function is included, and the radio receiver works in a range of average MW or long LW of waves, at detection of a signal of the transferred road message the radio receiver automatically will be switched from MW or LW range in a FM range and will be adjusted on the station transferring the road message. If the THAT function is switched off, and the radio receiver is adjusted on the station transferring the program of road messages, on the display the indicator "T" will burn. By pressing the THAT switch and inclusion of function of reception of road messages instead of the indicator "T" on the display the THAT indicator will burn.

Function of interruption of the current mode by the road message. If the THAT function is included, a radio receiver, having found translation of the road message, is adjusted on radio station which transfers this message, and loudness of a sound is established on previously set level. After the completion of translation of the road message the audiosystem comes back to that operating mode in which it was at the moment of interruption for reception of the road message. Level of loudness of a sound also is established on initial level. Reception of a radio program of the station entering into the expanded EON network, automatically interrupts, if the road message also is transferred by EON radio station. After the completion of translation of the road message the radio receiver will return to radio station reception on which it was adjusted previously. THAT function is switched off, if during translation of the road message to press one of the TA/PTY, BAND or SRC buttons.

Function of search of the program of road messages. If at the included THAT function the radio receiver could not be adjusted in all range on radio station which transfers the program of road messages, it comes back to reception previously the adjusted station. Thus on the audiosystem display for three seconds «NO TRAFFIC» message lights up.

Installation of level of loudness of a sound for translation of road messages. It is possible to establish previously loudness level for translation of road messages, having used the menu of personal control.

Choice such as a radio program

The PTY function provides possibility of a choice of the radio station transferring the program of a certain genre in a range of FM. At long (more than two seconds) pressing the TA/PTY button when the radio receiver works in a FM range and the PTY function is switched off, on the display is deduced the name of PTY type of an accepted radio program. At the included PTY function on the display the PTY indicator burns.

Mode of a choice of PTY type of a radio program. The choice of PTY type of a radio program is made by means of buttons ^ and v of manual setup of the receiver, or by means of buttons of setup of the receiver on previously programmed radio stations. Names of the first five PTY types of radio programs are stored in the corresponding cells of memory of a radio receiver. However, cells of memory can be reprogrammed. For this purpose it is necessary to deduce the name of demanded PTY type of a radio program on the audiosystem display and then it is long (not less than two seconds) to press one of five buttons of a choice previously the programmed radio stations. Thus chosen name of PTY type of a radio program will be brought in the corresponding cell of memory of a radio receiver.

Function of search of a radio program on the set PTY type joins in pressing one of buttons of automatic control of a radio receiver (<<or>>). In the course of such search on the display the message of "SEARCH" and the name of the set PTY type of a radio program are deduced periodically replacing each other. If it was not possible to find a demanded radio program, on the display for 2 seconds «NO PTY» message lights up. Then the radio receiver will continue to accept the radio station program on which it was adjusted previously. If the radio receiver was adjusted on station which broadcasts the program of the set PTY type, on the display there is a name of this radio station.

Menu of personal control of parameters

To enter into this menu, press power supply switch at the switched-off audiosystem, previously having pressed and holding in this situation the MOD switch. If to press the button ^ or v, on the display will replace consistently cyclically each other the following indicators of modes of installation: PTY lang (language of PTY messages: English, German or French), THAT volume (loudness level for translation of road messages), ON volume (initial level of loudness at audiosystem inclusion), HI CUT, PTY lang etc. Parameters of the chosen mode can be changed by means of buttons <<or>>. After control of parameters for entering them in memory of an audiosystem press the switch of power supply and switch off an audiosystem.

The HI CUT function improves quality of sounding of an audiosystem at reception of broadcasts in a FM range. In the presence of hindrances level of high frequencies automatically decreases. It promotes also to reduction of level of hindrances. Inclusion and switching off of the HI CUT function is made by pressing the button <<or>>. The condition of "HI CUT 1" corresponds to decrease in level of high frequencies, and «HICUT 0» condition – to absence of correction of a sound.

CD player

Turn a key or the ignition switch in the situation "Acc" or "ON" and insert CD into a loading window of the worker (without inscriptions) the party down. The disk will automatically be loaded into a player then reproduction of the first record will begin. If CD is loaded at a working radio receiver, reception of a radio program stops automatically and will begin disk playing.

Do not press a disk at its loading, it can result in malfunction of a player. To take a disk from a player press the button of extraction of a disk.

Consecutive choice of the beginning of record

Press the button>> or <<to pass to the beginning according to the following or current record on CD. In the course of search of the beginning of record the sound is switched off.

The accelerated listening of record

If to press the button ^ or v and to hold it more long than two seconds, continuous high-speed playback of records respectively in direct or in the opposite direction will begin. At high-speed playback the sound is muffled. High-speed playback of CD proceeds, while the pressed button will not be released.

Mode of repeated reproduction of record (RPT)

To include repeated reproduction of the current record, press the RPT button. Thus on the display for two seconds there will be a RPT TRAK indicator which then will be replaced by the RPT indicator. The mode of repeated reproduction of record is switched off by pressing one of buttons: «SRC» (duration of pressing not less than two seconds), «RPT» or «MIX».

Mode of reproduction of records in casual sequence (MIX)

To include a mode of reproduction of all records on CD in casual sequence, press the button of "MIX". Thus on the display for two seconds there will be an indicator of «the MIX DISC» which then will be replaced by the indicator "MIX". This mode is switched off by pressing one of buttons: «SRC» (duration of pressing not less than two seconds), «RPT» or «MIX».

Mode of the review of a disk

If it is long (not less than two seconds) to press the SRC button, the audiosystem will start to lose consistently initial 10-second fragments of each record on CD. The mode of the review of a disk is switched off by pressing one of buttons: «SRC» (duration of pressing not less than two seconds), «RPT» or «MIX».

Buttons of management of an audiosystem, located on a wheel

Steering switch of a sort of work (SRC)

Consecutive pressing the SRC button lead to cyclic switching of operating modes of an audiosystem: MW, LW, FM1, FM2, FMT, CD, MW etc. If the compact disc is not loaded, on the display there is «NO DISC» message.

Buttons of automatic control of a radio receiver or consecutive transition between records on CD (^ and v)

Pressing these buttons in a mode of radio it is possible to adjust consistently a radio receiver on previously programmed radio stations.

If at CD reproduction the mode "MIX" is switched off, at short (no more than two seconds) pressing the button ^ or v occurs transition to the following or previous record on CD; otherwise (a mode "MIX" is included) records on a compact disc will be lost in casual sequence.

Regulator of level of loudness of a sound (VOL)

Establish demanded loudness of a sound, pressing the regulator button up () or down (–).



2.4.2. Systems of ventilation, heating and air conditioning

2.5. Receptions of operation and auxiliary systems