Removal and installation of moldings and consolidations. Nissan Micra (since 2002 of release)
Service and to Nissan Micra car repairs (since 2002 of release)
1. Introduction
2. Governing bodies and operation receptions
3. Settings and routine maintenance of the car
4. Engine
5. Systems of cooling of the engine, heating, ventilation and air conditioning
6. A power supply system and production of the fulfilled gases
7. Systems of electric equipment of the engine
8. Manual box of gear shifting and coupling
9. Automatic transmission
10. Power shafts, rotary fists and stupichny assemblies
11. Brake system
12. Suspension bracket and steering
13. Body
13.1. External equipment and body elements
13.1.1. Removal and installation of a fairing of a windscreen
13.1.2. Removal and installation of a decorative front grille
13.1.3. Removal and installation of moldings and consolidations
13.1.4. Removal and installation of a front bumper and forward spoiler
13.1.5. Removal and installation of a rear bumper
13.1.6. Removal and installation of a forward wing and loker
13.1.7. Removal and installation of basic beams of a radiator
13.1.8. Removal, installation and cowl adjustment
13.1.9. Removal and installation of locks of a cowl and hatch of a fuel jellied mouth
13.1.10. Removal, installation and adjustment of a door of a back and the components interfaced to it
13.1.11. Removal, installation and adjustment of lateral doors
13.1.12. Removal and installation of locks and handles of doors
13.1.13. Removal, installation and adjustment of assembly of the top hatch and its components
13.1.14. Removal, installation and repair of an external rear-view mirror
13.2. Salon equipment
14. Onboard electric equipment
15. Electric equipment schemes
 







f4fb234a

13-1-3-snyatie-i-ustanovka-moldingov-i-uplotnenijj.html

13.1.3. Removal and installation of moldings and consolidations

Roof molding

Fastening of a molding of a roof


Other moldings are replaced similarly.


 PERFORMANCE ORDER

  1. Plastic wedge lift back edge of a molding of a roof, remove a clamp and cut a 2-foreign sticky tape of fastening of a molding.
  2. Remove the remains of a sticky tape from a molding and a body.
  3. Clear interfaced surfaces of a roof and a molding.
  4. Paste a clamp from a body and wait not less than 40 minutes.
  5. Put a first coat (for example, Sumitomo 3M N200) on a back surface of a clamp interfaced to a sticky tape from a body.
  6. Paste a sticky tape on the back party of a clamp from a body
  7. Join the forward party of a molding of a roof with windscreen consolidation, press a roof molding in front back and fix it on a body by means of a 2-foreign sticky tape and clamps.

Windscreen consolidation

 PERFORMANCE ORDER

  1. Remove a windscreen fairing (see. Section Removal and installation of a fairing of a windscreen).
  1. Disconnect from wings of their cover, having cut a 2-foreign sticky tape.
  1. Paste a protective tape on perimeter of consolidation of a windscreen and cut a consolidation sponge.
  1. Remove the remained consolidation.
  1. Put a first coat and glue.
  1. Level a white label on new consolidation of a windscreen with a label on a pro-rate at the top of a windscreen.
  2. Press hands consolidation so that its bottom small beard was hooked for glass, and then press consolidation in the direction outside.
  3. Remove a protective tape and establish covers of wings and a windscreen fairing.

Consolidations of glasses of lateral doors

Fixture of consolidations of glasses of lateral doors


 PERFORMANCE ORDER

  1. Completely lower door glass.
  2. Undertake consolidation and extend it up, liberating from clamps (since back).
  3. Installation is made in the return to a lock.



13.1.2. Removal and installation of a decorative front grille

13.1.4. Removal and installation of a front bumper and forward spoiler